Philips FW C788 Hook-up Manual

Crane Company One of the most useful and fun toys in my antenna arsenal is the C. Crane Twin Coil Ferrite antenna. I have used it with many radios from portables to large table tops and it has worked equally well with almost all of them. It can also make many radios far more convenient to use because of its immense adjustability and flexibility as you will see. The Twin Coil Ferrite Antenna is an active, amplified and tuned AM antenna designed to dramatically increase signal levels of weak and medium strength AM stations. It is a patented design using an ingenious method of extracting the maximum signal level out of its huge ferrite loopstick within the Antenna Element. It is connected via a 5 foot cord you can also buy 25 and 50 foot extensions if needed to the Tuner Control box which sits next to your radio. The Tuner Control Box holds a standard 9 volt battery which provides long life, or it can be used with the included 9 volt AC Adapter for more permanent installations. Crane Twin Coil Ferrite antenna is exceptionally flexible in terms of placement and method of connection.

Good AM/FM antenna

AM radio with spiral-wound coil and home-made tuning capacitor The radios described here are a regenerative design utilizing a single JFET and cheap audio amplifier integrated circuit. These radios therefore are designed to work well with no external antenna. Another design problem was the tuning capacitors. In the end I found a way to make them out of blank copper clad printed circuit board material. It ended up more educational anyway, since you can see exactly what it is, compared to the small plastic ones that were common in transistor radios.

The built-in radio antennas for AM usually do a good job, but if your radio has an external AM antenna connection on the back, a simple wire or loop can be of help. The orientation of the radio with its internal “bar” antenna can be important — always try rotating your AM radio to find the best signal.

I decided to build another one for a friend and will try to document the build in this post. When I built the first one I built I also built a pre amp but have decided to use just the loop passive design for the last two I made. Here is a link for the design of the first one I built. The hula hoop Be carful when choosing a hula hoop as some of them have lights in them and cost much more. The cheaper the better. Once you have the loop, separate it at the seam. Once separated pull the loop apart and dump the water or sand out of it.

I usually give it a few days to dry out which is easy in the dry climate of Colorado. Find the seam Pull to separate could take some effort Do not throw away the plastic part that joins to two halfs together. You will use this to figure out which FSC box will work.

Wind Your Own RF Matching/Isolation Transformer

Why the G5RV continues to remain popular is a mystery. The ‘legendary’ name, perhaps? That it can be ‘thrown up’ without too much thought? The fact that it’ cheap and cheerful? There has been much written about the G5RV and the overall conclusion is that it’s not a very good multi-band antenna.

2 Using the Small Loop Antenna Joseph J. Carr Small loop antennas have an overall wire length ≤ λ. They exhibit deep nulls perpendicular to the plane of the loop, and broad maxima off the ends of the loop.

Conti It’s the question I’m asked most often about broadband loop antennas such as the Delta, Flag, and SuperLoop; “Where can I find the matching transformer? Because the broadband loop antenna is floating no connection to ground , the antenna connections must be isolated from the lead-in. If the high impedance winding of the antenna is physically connected to the low impedance winding of the lead-in, then the loop antenna will no longer be floating which defeats the noise-reduced design of the inherently low-noise loop configuration.

Those commercially available matching transformers, often referred to as ‘baluns’, usually have an internal common ground connection between the high and low impedance windings. The common ground might be perfectly fine for dipole and vertical whip applications, but not for a loop. Therefore to guarantee isolation requires either hiring someone to build a custom transformer, or the more economical option – DIY – do it yourself.

Order an RF transformer from Mini-Circuits or an eBay seller , then complete the assembly by installing the Mini-Circuits trasformer in a plastic chassis with appropriate antenna and lead-in connectors. This is the easiest of the two DIY projects. However the Mini-Circuits transformers are so tiny that they can be blown up by static electricity or a nearby lightning strike. Although I’ve had relatively good experience with Mini-Circuits transformers, even I’ve lost a few over the years.

However, if the antenna is in a location where the risk of lightning is low, then you could probably get away with the Mini-Circuits DIY shortcut. If the transformer is mounted on a DIP socket, then at least it can be easily replaced if damaged. When placing a Mini-Circuits order, it’s a good idea to buy a couple extras just in case.

ANTENNAS FOR HAM TRANSMITTERS

Improving your AM AM Radio Reception – How to boost your reception- A 5 minute lesson on how you can dramatically increase your AM Radio’s signal, get rid of that horrible noise and static, and a look at what could be causing your problems. Why not just listen to the internet? AM Radios are portable and with the right AM antenna, you can listen to long distance radio stations, especially at night!

Oct 05,  · A Hardwired Loop For DSP Radios The introduction of DSP ultralight radios using the Silicon Labs Six chip about four years ago proved to be an experimenter’s playground. The new design allows for a simply-wound ferrite loopstick antenna with a single coil winding, connecting to the radio’s circuit board on just two soldered : RADIO-TIMETRAVELLER.

Thicker wire provides better reception and is more suitable for transmitting if you have a license but it is heavier. The antenna I’ve demonstrated at recent events uses 1mm thick wire. Smaller insulators are better as they are lighter and less expensive. You may want to buy more than one balun, for example, a 4: Make sure it is waterproof, has hooks for attaching a string or rope and an SO socket. The cable must be 50 ohm. There are even lighter and cheaper alternatives if you only need to receive.

Contact Dish Customer Service

Hence after having a good Receiver and a Transmitter or Transceiver , the next important item one should have to set up a ham radio station is a good antenna. The radio frequency power that is generated in the transmitter should be radiated in the form of electro magnetic waves. It is the job of the antenna to convert the RF power into radio waves and radiate them into the desired direction for effective communication. For this purpose, the antenna should be located well above the ground and it should be kept away from any tall buildings, trees, electrical power conductors, telephone and telegraph wires and other metal objects that will absorb the energy.

The antenna should be erected as high as possible for the best results. Antennas has reciprocity in that a good transmitting antenna will also work as a good receiving antenna.

FM radio receivers need an antennae to pick up the signal a radio station transmits. FM radio signals are a much higher frequency than AM and therefore have a much more limited range.

This shows a restored video signal after the Humbucker is installed. Ground loop Interference looks like a wavy line superimposed on the normal video signal. This image illustrates a moderate video ground loop problem. Note the three gray horizontal bands. The bands move up through the picture. What does it sound like? Click the button to hear the 60 Hz hum. Audio hum, cycle noise, 60 Hz hum, similar to the lowest note on a bass guitar or bass drum.

Technics Tuner ST-G70l – How can I recieve am with out orginal AM loop jack?

Any number of situations may call for these measures but the antenna system must still work! Federal law backs up that requirement for licensed Ham radio stations. The power of group pressure. In any event, a brief presentation to the HOA Board resulted in approval.

Addwards ALMS SW/AM/LW Loop Antenna The Addwards ALMS is an active (amplified) Loop Antenna covering SW/AM/LW bands selling currently for $ – $22 plus shipping depending on source. Even the most frugal radio hobbyist would have to admit that is downright cheap if the thing works at all it would be quite a value at the very.

Model Receiver Parts ldentification Notes We rely on you to know already what a resistor, transistor, lC “chip” and other common electronic parts “look like. Both the back and inside front covers of this manual provide some light-hearted help on basic parts identification. Each assembly step provides useful help in identifying any part, whether by shape, color-code, manufacturer’s markings, or other description.

The Zener, and Varactor diodes must be identified exactly. Our protocol is to identify those in picofarads up to 99 pF simply as 1 pF or 33 pF, etc. There may be one letter to identify temperature characteristics e. Building Electronic Kit Projects: Both this manual and the engineering discipline for this receiver were done with YOU very much in mind. Here’s what is important: To get a good fit of the LED’s and 3- digit displays, you’ll be handling the front panel and display lens – be VERY careful not to touch these with your soldering iron!

Page 23 Before you do ANY soldering, we remind you again to do the following: Check and organize your kit parts in whatever way Is most convenient for you. Go through this entire manual:

Free Internet TV – A Complete Guide For Canadians

If so there are several possibilities. First you want to decide if you want an Inside Antenna or an Outside antenna. If an outside one..

Antennas to improve you AM, FM, or WiFi reception. Increase your connection with one of C Cranes long range antennas.

That is certainly the case with the basic “loop” antenna, an often misunderstood critter, but one that gives absolutely the most for each foot of wire of any antenna I have had occasion to play with. They are long, long, long Who has room for over feet of wire in the case of a full-wavelength loop for meters?

Won’t that thing become the perfect conduit right into my house for lightning and other “wrath of God” type things? And will it work on more than one band? I don’t want something that big in my yard if it only gets me a narrow swatch of one band. First, let me reassure you that such an antenna does not necessarily take much room.

AM Loop Antenna – Very Effective – DIY


Greetings! Do you want find a sex partner? Nothing is more simple! Click here, free registration!